Building Electric Fireplace Into Wall

The concept of building an electric fireplace into the wall is a very popular one. You can do this by creating a hole in the wall and cutting out a space for the fireplace to sit. Then, you will need to install wood framing around this area and attach it with screws or nails. Next, you will have to add drywall over this framing and paint it over. This process can be done by yourself if you have some experience with DIY projects but it might be better if you hire an expert for this job.

Before you start building your electric fireplace into a wall, there are some things that you’ll need to consider first. You’ll need to make sure that the space where it will go has enough room for both the fireplace and for installing all necessary wiring and hardware needed for operation. If it doesn’t have enough room, then you may need to choose another location instead. The next thing is deciding whether or not you want this type of fireplace in an enclosed room or open space like the living room or dining room. This will depend on what kind of look or feel do want in those areas. The last thing is choosing between a freestanding model versus a recessed model. Recessed models tend

The construction of an electric fireplace into a wall is a relatively simple process. The first step is to decide where you want to place your fireplace. For example, you may have a wall that does not have any decorative purpose and would be suitable for a fireplace.

The next step is to measure the width and height of the area you want to build your fireplace. You will need these measurements when ordering your materials so that everything fits properly and looks attractive once installed.

Once you have determined where your fireplace will be located, you can begin building it. First, cut out a section of drywall large enough for the width and height of the unit (usually about 36 inches by 24 inches). Next, install one piece of drywall on each side of this opening using screws or nails so that there is enough room for attaching other pieces later without overlapping them by too much space between them at all times during the installation process; otherwise, this could cause problems with attaching brackets onto walls/ceilings that hold weight from above without any cracks showing up later on down road during the use time frame when heavy loads placed in front of the fireplace (so far so good.

Want to add a fireplace to your home, but not sure where to put it? If you’re looking for something that’s easy on the eyes and convenient, consider building an electric fireplace into your wall. These can be incorporated into any room of your house, so long as you have an electrical outlet nearby. Electric fireplaces are also safe and have no heat source. They work by heating up a small metal coil inside which then produces infrared rays that provide warmth without flames or smoke.

What is An Electric Fireplace

An electric fireplace is a fireplace that uses electricity, instead of wood or gas, to create heat and flames. It can be installed in any room in your house and used for heating or cooling purposes. They are also decorative features that look great when added to any room’s décor.

Electric fireplaces come in many different styles and designs, so you’re sure to find one that fits your needs perfectly.

Reasons for Building Electric Fireplace Into Wall

You might be wondering, why would I build an electric fireplace into my wall. Here are 4 reasons:

  • You can use it as a heat source.
  • You can control it from your phone.
  • It’s perfect for adding a striking feature to your home and
  • Can be installed on a wall or on a mantel

Steps involved in Building Electric Fireplace Into Wall

Now that you’ve decided to build an electric fireplace into the wall, it’s time to start the project. The first step is preparing the location, which is probably easiest if you have an existing fireplace or a hole in your wall where one was previously installed. The next steps involve assembling the fireplace unit and cutting out an opening for it in the wall.

Once you have a rough opening cut out, it’s time to build a framed opening using 2×4 studs and plywood sheathing (or paneling if this is going on an exterior wall). Then, install your new electric firebox as well as its surround frame before finishing up with electrical connections and any final touches such as painting or grouting around tile worktops

Preparing the Location

Before you get started with actually installing the fireplace, it’s important to make sure you have picked the right spot. You need to measure the size of your new fireplace and make sure there is enough space for it all.

  • The first thing you must do is check out the size of the electric fireplace itself. This will determine whether or not it can fit in your current wall, and whether or not there will be room for a surround around it (which both adds aesthetic value and helps keep heat from escaping).
  • Likewise, if you want surround lighting around your electric firebox then this too needs enough room so make sure that if there is going to be a lampshade above your unit, then there will be enough space between them so they don’t collide during installation/operation.

Preparing the Fireplace Unit

  • Remove the fireplace from its box and check that all parts are present. If you see anything missing, contact the manufacturer immediately.
  • Check that the unit is in good condition no cracks or dents on any of the surfaces. If there are any problems, try to work through them before beginning installation because replacing a damaged component will likely require new tools as well as a return trip to get a different part.
  • Verify whether or not your wall has been prepared for an electric fireplace by checking for electrical outlets within reach of each end of where you want your fireplace mounted into the wall; if there aren’t any existing outlets nearby, look at how much wiring will be required in order to have power running directly into where you’ll be mounting your unit (this may vary depending on what type of outlet(s) need installing).

Cutting the Opening

  • Use a jigsaw to cut the opening on your wall. Make sure you have enough space for the fireplace and that it will fit snugly within the opening.
  • Mark an outline with a pencil onto your wall, keeping it level with the surface of the wall.
  • Cut along this line with a jigsaw or other saw (if you don’t have access to one, check out Habitat For Humanity’s ReStore).

Building a Framed Opening

After you have framed the opening for your electric fireplace, it’s time to cut it out.

You can use a handsaw or circular saw to make this cut, but if you want a perfectly clean edge and precise measurements, I recommend using a skill saw with a masonry blade on it (see image below).

  • Make sure that all of your cuts are made with the blade at 90 degrees to the bottom of your wall (not at an angle) and that they are smooth with no bumps or pulls left in them. A jagged cut will make putting up crown molding tricky later on when we install it overtop of them.

Installing the Fireplace Unit and Building the Surrounding Wall

  • The fireplace unit should be installed first.
  • Then, create a firebox and build the surrounding wall around it.

Final Touches and Electrical Connections

  • Install the surround.
  • Install the fireplace unit.
  • Connect your fireplace to a power supply, if applicable.
  • Install the remote control, if applicable.

Benefits of Building Electric Fireplace Into Wall

In addition to the aesthetic appeal of an electric fireplace, there are several benefits of building one into your wall. It’s easy to install and can make a great focal point in any room. The cost is much lower than that of gas or wood-burning fireplaces. You can control it from your smartphone, and it’s even easier to clean than most other types of fireplaces.

Materials needed for Building Electric Fireplace Into Wall

Materials:

  • Electric fireplace
  • The frame (wood)
  • Glass panes, tempered glass, or glass tiles

Tools:

  • Routers
  • Drill press

Costs: Building an electric fireplace into the wall is not a cheap project. In fact, it can cost over $100 per linear foot to install one of these units in your home. You’ll need to factor in the cost of labor and materials when deciding whether or not building an electric fireplace into your walls is worth it for you. Maintenance tips: If you want to make sure that your new electric fireplace stays beautiful and safe for years to come, there are several maintenance tips that can help keep it looking great.

Tools needed for Building Electric Fireplace Into Wall

You will need a few basic tools to build your electric fireplace into the wall. To get started, you’ll want to gather:

  • Electric saw
  • Drill with hammer drill bit(s) and masonry bit(s)
  • Caulking gun (if you’re caulking your electric fireplace)
  • Pliers or adjustable wrench (for tightening bolts)
  • Tape measure and level (for measuring distance between studs)

Costs of Building Electric Fireplace Into Wall

The average cost of building an electric fireplace into your wall can range from $200 to $1,000 depending on how much you want to spend and whether you choose to hire a contractor or do it yourself. The cost will also depend on the size of the unit, but generally speaking, you should expect to pay between $100 and $300 for each linear foot of wall space in your home. For example: if you have 3 feet of wall space that needs an electric fireplace, expect bills between $300 and $900 based on average prices charged by contractors in your area.

Maintenance tips for Building Electric Fireplace Into Wall

To get the most out of your electric fireplace, it’s important to keep it clean and well-maintained. Here are some tips on what you can do:

  • Clean the glass regularly with a damp cloth or paper towel. If you want to remove any dust from inside the fireplace, use a soft bristle brush that won’t scratch up your hearthstone.
  • Check the pilot light regularly so you know if there’s something wrong with it or if it needs to be cleaned. You’ll also want to check that no hair has fallen into or near where your pilot light will be located when using this feature of your fireplace built into the wall project.
  • Check the temperature gauge regularly so you know when there might be an issue with how hot or cold things are getting in this area of your house (or apartment). This could mean having trouble sleeping at night because something is off with either too much heat coming through these vents right above head level while lying down; perhaps there’s not enough warmth coming through them during winter months when everyone wants an extra blanket wrapped around themselves instead.
  • Check the thermostat regularly so they don’t malfunction unexpectedly like last time those were dark days indeed. Plus now there’s less risk for breakage since we’ve gone ahead and installed those new ones during the project planning stages earlier this week.

Building an electric fireplace into your wall can be a beautiful way to add a striking feature to your home. You can even operate these from your smartphone.

There are many different designs and colors of electric fireplaces, so it’s easy to find one that meets the needs of you and your home. They’re great for heating or just ambiance when it’s cold outside, so they’ll do more than just look pretty they’ll help keep you warm during the winter months.

Electric fireplaces also come with different features such as USB ports or Bluetooth capabilities that allow you to stream music through speakers placed inside them. You can set them up, however, whatever works best for you.

Final words

Building an electric fireplace into your wall can be a beautiful way to add a striking feature to your home. You can even operate these from your smartphone.

Leave a Comment

error: Content is protected !!